- Pneumatic
- Powered by compressed air from a compressor, rather than electricity or hydraulic oil. All ACE hand tools are pneumatic.
- Hydraulic
- Powered by oil under pressure. Our rock breakers are hydraulic and run off the excavator's hydraulic system.
- bpm (blows per minute)
- How many times the piston strikes the chisel each minute. A higher rate gives faster, lighter blows; a lower rate with a long stroke gives heavier blows.
- Piston diameter or bore
- The width of the piston inside the tool. A bigger piston gives more energy per blow.
- Stroke
- How far the piston travels before it hits the chisel. A longer stroke gives a harder blow at a slower rate.
- Air consumption (l/s, cfm)
- How much compressed air the tool uses, which decides the size of compressor you need. 1 l/s is about 2.1 cfm.
- Air pressure (bar, psi)
- The working air pressure. Almost all ACE tools run at 6 to 7 bar (87 to 100 psi). 1 bar is about 14.5 psi.
- Shank
- The end of a chisel or drill steel that goes into the tool. It must match the tool, and is given as a shape and size: 25 × 108 mm hex means a hexagon 25 mm across the flats and 108 mm long.
- Retainer or latch
- The catch on the front of the tool that holds the chisel in. A latch or kick latch retainer releases quickly; a spring or cap retainer is simpler.
- Moil point, narrow chisel, wide chisel, asphalt cutter, clay spade
- Chisel tip shapes. A moil point (also called a bull point) is for general breaking, a narrow or wide chisel for cutting and splitting, an asphalt cutter (tarmac cutter) for asphalt, and a clay spade for digging soil.
- Steel
- A word you will see on other sites for any chisel or drill rod, as in breaker steel or drill steel. On this site we call breaker steels chisels.
- D handle, T handle, pistol grip (P)
- Handle styles. A D handle is for pushing down, a T handle with two side grips is used on large breakers, and a pistol grip is for horizontal work.
- SVR
- Silenced, vibration reduced. A version of the tool with a silencer and vibration damped handles, for sites with noise or hand arm vibration limits.
- OEM part number
- The part number the original manufacturer (Atlas Copco, CP, TOKU and others) uses for the same tool or part. Quote it and we can confirm the ACE part is a direct replacement.
- Equivalent to, interchangeable with
- The ACE tool takes the same chisels and spare parts as the named model from another brand.
- CP
- Chicago Pneumatic, a US brand. Many ACE tools take the same chisels and spares as CP models such as the CP 1210, CP 4123 and CP 0006.
- TEX
- Atlas Copco's range of pneumatic breakers and pick hammers, such as the TEX 05 PS and TEX P60.
- TOKU
- A Japanese pneumatic tool brand known for its TPB breakers and TCA pick hammers.
- La Cruz
- A Spanish pick hammer brand, maker of the ML 33 and M 37B.
- Paving breaker, road breaker, concrete breaker, jackhammer
- Different names for the same tool: a heavy upright air hammer for breaking concrete and roads.
- Chipping hammer
- A light air hammer for chipping, scaling and cleaning welds.
- Rivet buster
- A long stroke hammer first made for cutting rivets, now also used as a compact demolition hammer for steel and concrete.
- Scabbler
- A tool with carbide tipped pistons that roughen or strip a concrete surface.
- Needle scaler or needle gun
- A tool with a bundle of steel needles that hammer rust, paint and scale off a surface.
- Rammer or tamper
- A pole shaped tool that compacts sand or soil.
- Rock drill or sinker drill
- A handheld air drill that hammers and rotates a drill steel to make holes in rock, usually for explosives.
- Jackleg drill or air leg drill
- A rock drill mounted on a telescopic air leg (pusher leg) for drilling horizontally into a tunnel face.
- Pusher leg or air leg
- The telescopic aluminium cylinder that supports a jackleg drill and pushes it forward.
- Drifter
- A large rock drill mounted on a rig or feed beam rather than held by hand.
- DTH (down the hole) hammer
- A hammer that goes down the hole on the end of the drill pipe and strikes the bit directly, for deep, large holes such as water wells and quarry blast holes.
- Flushing (air or water)
- Blowing air or water down the hollow drill steel to clear rock chips out of the hole. Water flushing is used underground to keep dust down.
- Blast hole, bench drilling, long hole drilling
- Types of drilling in quarries and mines: holes for explosives, drilling down from a step (bench) in an open pit, and deep production holes underground.
- Drift, stope, narrow vein
- Underground mining terms: a horizontal tunnel, the space where ore is mined, and a thin ore body that needs small, low equipment.
- Integral drill steel
- A one piece drill rod with a carbide chisel tip forged on. It is replaced when worn.
- Tapered rod and tapered button bit
- A two piece system: a reusable rod with a cone shaped end, and a replaceable carbide button bit that is pressed onto it. The taper angle (7° or 11°) must match.
- Extension rod, coupling sleeve, shank adaptor
- Threaded rods (R32, T38, T45, T51 and others) are joined by coupling sleeves to reach deep holes with drifters. The shank adaptor connects the rods to the drill.
- R22, R25, R32, R38, T38, T45, T51
- Standard rock drilling thread sizes. R is a rope thread, T is a trapezoidal thread, and the number is roughly the diameter in mm.
- Button bit
- A drill bit with tungsten carbide buttons set in its face. Gauge buttons sit on the outer edge and face buttons in the centre.
- TCT
- Tungsten carbide tipped: a hard metal insert that does the cutting.
- M4 and K4 shank
- DTH bit shank profiles. The bit and the hammer must use the same shank.
- API 2 3/8 inch Reg
- A standard oilfield thread used to connect a DTH hammer to the drill pipe.
- Impact energy (J, ft lb)
- The energy in each blow of a hydraulic breaker, given in joules. 1 J is about 0.74 ft lb.
- Carrier
- The excavator weight class, in tonnes, that a hydraulic breaker is made to fit.
- Piston, front head, chisel (breaker spares)
- The three main wear parts of a hydraulic breaker: the piston that strikes, the front head that guides the tool, and the tool itself (chisel, moil or blunt).
- Air line lubricator or line oiler
- A small oil reservoir in the air line that feeds an oil mist to the tool. It keeps the tool working and cuts wear.
- Laitance
- The weak, milky top layer of cured concrete. It has to be removed, for example by scabbling, before an overlay or coating will stick.